id | field name | definition |
0 | mcmd_execution_field |
binary uint16 | size: 2 |
Macrocommand Execution Field
|
|
1 | mpd_relay_contact_ods_status |
binary uint16 | size: 2 |
MPD Relay Contact / ODS Status
|
|
2 | direct_voltage_current_status |
binary uint16 | size: 2 |
Direct Voltage/Current Status
|
|
3 | idu_status |
binary uint16 | size: 2 |
IDU Status. Least significant byte denotes forward/reverse sweeps; 0 = counterclockwise; 1 = clockwise sweep.
|
|
4 | idu_error_status |
binary uint16 | size: 2 |
IDU Error Status
|
|
5 | heater_power_level_relay_status |
binary uint16 | size: 2 |
Heater Power Level and Relay Status
|
|
6 | asu_cmd_status |
binary uint16 | size: 2 |
ASU Command Status
|
|
7 | asu_direct_status |
binary uint16 | size: 2 |
ASU Direct Status
|
|
8 | esu_cmd_status |
binary uint16 | size: 2 |
ESU Command Status
|
|
9 | esu_direct_status |
binary uint16 | size: 2 |
ESU Direct Status
|
|
10 | spe_config_status |
binary uint32 | size: 4 |
SPE Configuration Status
|
|
11 | fca_status |
binary array[6] | size: 12 |
FCA Status
|
|
12 | sw_cmcd_status |
binary uint16 | size: 2 |
SW Command Status
|
|
13 | dpu_detector_thermistor_1 |
binary uint16 | size: 2 |
Thermistor #1 temperature at the detectors (12 bits, range 0--337K)
|
|
14 | dpu_detector_thermistor_2 |
binary uint16 | size: 2 |
Thermistor #2 temperature at the detectors (12 bits, range 41--91K)
|
|
15 | latest_scan_gate_start_time |
binary uint32 | size: 4 |
Latest Scan Gate Start Time
unit: "1/256 s"
|
|
16 | previous_scan_gate_start_time |
binary uint16 | size: 2 |
Previous Scan Gate Start Time
unit: "1/256 s"
|
|
17 | end_identifier_1 |
binary uint16 | size: 2 |
Constant value (FFFF, hex).
|
|
18 | substeps_heater_mode |
binary uint16 | size: 2 |
Substeps to Heater Mode
|
|
19 | aps_pos_last_scan_gate_start |
binary uint32 | size: 4 |
APS Position at Last Scan Gate Start
|
|
20 | aps_pos_last_scan_gate_stop |
binary uint32 | size: 4 |
APS Position at Last Scan Gate Stop
|
|
21 | measured_az_los |
binary uint32 (double) | size: 4 |
Measured Azimuth LOS
unit: "1e-5 degrees"
converted unit: "degrees" (multiply by 1/100000)
|
|
22 | measured_el_los |
binary uint32 (double) | size: 4 |
Measured Elevation LOS
unit: "1e-5 degrees"
converted unit: "degrees" (multiply by 1/100000)
|
|
23 | low_level_currents |
binary array[5] | size: 10 |
Low Level Currents
|
|
24 | ice_box_a_temp_radiator |
binary uint16 | size: 2 |
ICE box A temp (radiator)
|
|
25 | ice_box_b_temp_radiator |
binary uint16 | size: 2 |
ICE box B temp (radiator)
|
|
26 | icu_power_supply_temp |
binary uint16 | size: 2 |
ICU power supply temp
|
|
27 | fde_power_supply_temp_1 |
binary uint16 | size: 2 |
FDE power supply temp 1
|
|
28 | fde_power_supply_temp_2 |
binary uint16 | size: 2 |
FDE power supply temp 2
|
|
29 | spe_box_temp |
binary uint16 | size: 2 |
SPE box temp
|
|
30 | spe_power_supply_temp_1 |
binary uint16 | size: 2 |
SPE power supply temp 1
|
|
31 | spe_power_supply_temp_2 |
binary uint16 | size: 2 |
SPE power supply temp 2
|
|
32 | paw_box_temp |
binary uint16 | size: 2 |
PAW box temp
|
|
33 | mio_base_plate_temp_1 |
binary uint16 | size: 2 |
MIO base plate temp 1
|
|
34 | mio_base_plate_temp_2 |
binary uint16 | size: 2 |
MIO base plate temp 2
|
|
35 | mio_base_plate_temp_3 |
binary uint16 | size: 2 |
MIO base plate temp 3
|
|
36 | aft_baffle_temp_1 |
binary uint16 | size: 2 |
aft baffle temp 1
|
|
37 | aft_baffle_temp_2 |
binary uint16 | size: 2 |
aft baffle temp 2
|
|
38 | side_baffle_temp |
binary uint16 | size: 2 |
side baffle temp
|
|
39 | fps_housing_temp_1 |
binary uint16 | size: 2 |
FPS housing temp 1
|
|
40 | fps_housing_temp_2 |
binary uint16 | size: 2 |
FPS housing temp 2
|
|
41 | asu_housing_temp_1 |
binary uint16 | size: 2 |
ASU housing temp 1
|
|
42 | ope_temp |
binary uint16 | size: 2 |
OPE temperature
|
|
43 | esu_temp_1 |
binary uint16 | size: 2 |
ESU temp 1
|
|
44 | not_used_temp_1 |
binary uint16 | size: 2 |
Not used
|
hidden: true
|
45 | not_used_temp_2 |
binary uint16 | size: 2 |
Not used
|
hidden: true
|
46 | telescope_temp |
binary uint16 | size: 2 |
Telescope temp
|
|
47 | ice_box_a_temp_doubler |
binary uint16 | size: 2 |
ICE box A temp (doubler)
|
|
48 | idu_temp_1 |
binary uint16 | size: 2 |
IDU temp 1 (center wall rear)
|
|
49 | idu_temp_2 |
binary uint16 | size: 2 |
IDU temp 2 (cent. wall near beam splitter)
|
|
50 | idu_temp_3 |
binary uint16 | size: 2 |
IDU temp 3 (center wall top)
|
|
51 | interferometer_souding_temp_1 |
binary uint16 | size: 2 |
INT housing temp 1 (foot near FPS)
|
|
52 | interferometer_souding_temp_2 |
binary uint16 | size: 2 |
INT housing temp 2 (paraffin actuator)
|
|
53 | interferometer_souding_temp_3 |
binary uint16 | size: 2 |
INT housing temp 3 (foot rear)
|
|
54 | fce_temp |
binary uint16 | size: 2 |
FCE temp
|
|
55 | not_used_temp_3 |
binary uint16 | size: 2 |
Not used
|
hidden: true
|
56 | not_used_temp_4 |
binary uint16 | size: 2 |
Not used
|
hidden: true
|
57 | not_used_temp_5 |
binary uint16 | size: 2 |
Not used
|
hidden: true
|
58 | not_used_temp_6 |
binary uint16 | size: 2 |
Not used
|
hidden: true
|
59 | fcu_temp |
binary uint16 | size: 2 |
FCU temp
|
|
60 | fca_radiator_temp |
binary uint16 | size: 2 |
FCA_radiator_temp
|
|
61 | olb_box_a_temp |
binary uint16 | size: 2 |
OLB box A temp
|
|
62 | old_box_b_temp |
binary uint16 | size: 2 |
OLB box B temp (not active laser box must be monitored for maintaining a minimum temperature)
|
|
63 | mio_if_bracket_temp_1 |
binary uint16 | size: 2 |
MIO I/F bracket temp 1
|
|
64 | mio_if_bracket_temp_2 |
binary uint16 | size: 2 |
MIO I/F bracket temp 2
|
|
65 | mio_if_bracket_temp_3 |
binary uint16 | size: 2 |
MIO I/F bracket temp 3
|
|
66 | mio_radiator_temp |
binary uint16 | size: 2 |
MIO radiator temperature
|
|
67 | mpd_temp |
binary uint16 | size: 2 |
MPD temp
|
|
68 | ice_box_b_temp_doubler |
binary uint16 | size: 2 |
ICE box B temp (doubler)
|
|
69 | dbu_temp |
binary uint16 | size: 2 |
DBU temp
|
|
70 | voltage_channels |
binary array[28] | size: 56 |
The current baseline assumes none of these values are used, hence no detailed formats are provided here.
|
|
71 | cbb_hk_parameters |
binary array[11] | size: 22 |
Temperature and Voltage information from the CBB.
|
|
72 | cbb_prt_readout_1 |
binary uint16 | size: 2 |
Temperature readout from CBB base #1
|
|
73 | cbb_prt_readout_2 |
binary uint16 | size: 2 |
Temperature readout from CBB base #2
|
|
74 | end_identifier_2 |
binary uint16 | size: 2 |
Constant value (FFFF, hex).
|
|
75 | spe_mode |
binary uint16 | size: 2 |
SPE Mode (transmission rate)
|
|
76 | spe_clck |
binary uint32 | size: 4 |
SPE Clock Cycles per IGM
|
|
77 | last_comm_sait_id |
binary uint16 | size: 2 |
Last commanded SAIT ID (high byte: elevation; low byte: azimuth)
|
|
78 | last_comm_no_sweeps |
binary uint16 | size: 2 |
Last commanded number of sweeps
|
|
79 | comm_low_fringe_count |
binary uint32 | size: 4 |
Commanded Low Fringe Count
|
|
80 | comm_high_fringe_count |
binary uint32 | size: 4 |
Commanded High Fringe Count
|
|
81 | comm_speed_rev_offs_cw |
binary uint16 | size: 2 |
Commanded Speed Reversal Offset (sr to cw)
|
|
82 | comm_speed_rev_offs_ccw |
binary uint16 | size: 2 |
Commanded Speed Reversal Offset (sr to ccw)
|
|
83 | comm_static_pos_slide_1 |
binary uint16 | size: 2 |
Commanded Static Position Slide #1
|
|
84 | comm_static_pos_slide_2 |
binary uint16 | size: 2 |
Commanded Static Position Slide #2
|
|
85 | comm_cross_over_pos |
binary uint16 | size: 2 |
Commanded cross-over position
|
|
86 | last_comm_el_start_angle |
binary uint32 (double) | size: 4 |
Last commanded elevation start angle
unit: "1e-5 degrees"
converted unit: "degrees" (multiply by 1/100000)
|
|
87 | last_comm_az_start_angle |
binary uint32 (double) | size: 4 |
Last commanded azimuth start angle
unit: "1e-5 degrees"
converted unit: "degrees" (multiply by 1/100000)
|
|
88 | obt_start_last_scan_seq |
binary uint32 | size: 4 |
OBT at start of last scan sequence
unit: "1/256 s"
|
|
89 | cbb_prt_readout_3 |
binary uint16 | size: 2 |
Temperature readout from CBB base #3
|
|
90 | cbb_prt_readout_4 |
binary uint16 | size: 2 |
Temperature readout from CBB base #4
|
|
91 | cbb_prt_readout_5 |
binary uint16 | size: 2 |
Temperature readout from CBB base #5
|
|
92 | cbb_cal_param_high_res |
binary array[5] | size: 10 |
CBB Calibration parameters (high resistance)
|
|
93 | cbb_cal_param_low_res |
binary array[5] | size: 10 |
CBB Calibration parameters (low resistance)
|
|
94 | rem_thermistor_channels |
binary array[14] | size: 28 |
Remaining thermistor channels
|
|
95 | rem_voltage_channels |
binary array[8] | size: 16 |
Remaining Voltage channels
|
|
96 | rem_lowlevel_voltage_channels |
binary array[7] | size: 14 |
Remaining low-level voltage channels
|
|
97 | spe_status |
binary array[41] | size: 82 |
SPE Status
|
|
98 | comm_redun_config |
binary array[5] | size: 10 |
Commanded redundancy configuration
|
|
99 | paw_comm_gain_bias_tables |
binary array[17] | size: 34 |
PAW Commanded Gain and Bias Tables
|
|
100 | spe_chan_delays |
binary array[4] | size: 8 |
SPE Channel Delays
|
|
101 | spe_band_mapping |
binary array[3] | size: 6 |
SPE Band Mapping
|
|
102 | spe_band_filter_sets |
binary array[2] | size: 4 |
SPE Band Filter Sets
|
|
103 | spe_decim_factors |
binary array[7] | size: 14 |
SPE Decimation Factors
|
|
104 | spe_timeout |
binary array[3] | size: 6 |
SPE Timeout
|
|
105 | asu_self_test_res |
binary array[2] | size: 4 |
ASU Self Test results
|
|
106 | esu_self_test_res |
binary array[2] | size: 4 |
ESU Self Test results
|
|
107 | fca_status_and_monitoring |
binary array[57] | size: 114 |
FCA Status and Monitoring
|
|
108 | prev_scan_gate_start_time |
binary uint32 | size: 4 |
Previous Scan Gate Start Time
|
|
109 | ice_instr_mode_act |
binary uint16 | size: 2 |
ICE Instrument Mode / Activity
|
|
110 | not_used_1 |
binary uint16 | size: 2 |
Not Used
|
hidden: true
|
111 | idx_el_start_angle_corr |
binary uint16 | size: 2 |
Index for elevation start angle correction table
|
|
112 | idx_az_start_angle_corr |
binary uint16 | size: 2 |
Index for azimuth start angle correction table
|
|
113 | not_used_2 |
binary array[5] | size: 10 |
Not Used
|
hidden: true
|
114 | asu_esu_pos_data |
binary array[257] | size: 514 |
Measured ASU/ESU Position Data
|
|
115 | spe_operating_mode |
binary uint16 | size: 2 |
SPE operating mode
|
|
116 | timeout_settings |
binary array[3] | size: 6 |
Timeout settings
|
|
117 | filter_set_ident |
binary uint16 | size: 2 |
Filter Set Identifiers
|
|
118 | filter_template_identifiers |
binary uint32 | size: 4 |
Filter Template Identifiers
|
|
119 | band_mapping_config |
binary array[3] | size: 6 |
Band Mapping Configuration
|
|
120 | channel_delay_settings |
binary array[8] | size: 16 |
Channel Delay Settings
|
|
121 | num_sampl_igm |
binary uint32 | size: 4 |
Number of samples in IGM
|
|
122 | volt_monitor |
binary array[9] | size: 18 |
Voltage Monitor
|
|
123 | asp_temp_mon |
binary array[4] | size: 8 |
ASP Temperature Monitor
|
|
124 | chan_stat |
binary array[16] | size: 32 |
Channel Statistics
|
|
125 | dsp_control_register_status |
binary array[4] | size: 8 |
DSP Control Register Status
|
|
126 | dsp_status_register_status |
binary array[4] | size: 8 |
DSP Status Register Status
|
|
127 | dec_factors |
binary array[8] | size: 16 |
Decimation Factors
|
|
128 | act_op_config_reg_stat |
binary array[17] | size: 34 |
Active OP Config Register Status
|
|
129 | self_test_conf |
binary array[6] | size: 12 |
Self Test Configuration
|
|
130 | sbit_edac_stats |
binary uint16 | size: 2 |
Single-bit EDAC Statistics
|
|
131 | last_sbit_edac_fault_addr |
binary uint16 | size: 2 |
Last single-bit EDAC fault address
|
|
132 | asp_latchup_err_flags |
binary uint16 | size: 2 |
ASP latch-up error flags
|
|
133 | warn_flags |
binary uint16 | size: 2 |
Warning Flags
|
|
134 | err_flags |
binary uint16 | size: 2 |
Error Flags
|
|
135 | not_used_3 |
binary array[7] | size: 14 |
Values nominally set to zero in format.
|
hidden: true
|